TopoContourDXF

1-foot plat map contours

Generate one-foot or two-foot parcel contours from a survey in feet. Compare the lines with spot grades and a known benchmark before using the DXF as a plat-map background. Preview free. Three exports cost $14.99.

Terrain viewport

Terrain sheet
Loading terrain…Synthetic DEM
Elevation range—
Index / minor—
Polyline vertices—

Elevation profile

A — A′
48%

Slope distribution

% GRADE

Free proof

Download a watermarked plan or the five highest contour elevations.

PROFESSIONAL EXPORTS

Pro Preview

DXF / SVG / GIS

Project pack 3 exports
CAD Pro Unlimited
Engineering Studio Unlimited

Match a one-foot interval to the survey

An interval of one foot says how far apart neighboring contours are vertically. It does not say how closely the field crew measured points, how accurate the vertical observations were, or where the legal boundary lies. A one-foot map can be appropriate on a modest lot with dense spot levels. The same setting on a coarse regional grid can give an impression of fine detail without adding any observations.

On a typical site sheet, examine the relationship among the curb, the proposed entry and the low portion of the yard. Spot levels at those places can be more informative than the apparent smoothness of the curves between them. If a retaining wall separates two grades at nearly the same horizontal location, a single continuous interpolated surface may smooth across a real discontinuity. Carry the surveyed top and bottom information separately for design.

For a reviewer, state whether the displayed contours describe existing ground or a proposed layout. Keep the plan date and survey reference nearby. A field level taken after grading can legitimately differ from an earlier plat background. Establish the date, units and datum before investigating a discrepancy as a drafting error.

Foot intervals expressed in meters

ParameterSpecification
International foot0.3048 m
Two-foot interval0.6096 m
Five-foot index1.524 m
Ten-foot index3.048 m

Worked examples

A lot with four feet of relief

Suppose ground rises from 700.2 feet at the front to 704.2 feet at the rear. Between those values the one-foot levels are 701, 702, 703 and 704. At two-foot spacing only 702 and 704 lie inside the range. A whole-foot sequence starts on its elevation grid, independent of the lot's minimum.

A shallow sidewalk connection

A one-foot rise spread across 50 horizontal feet averages two percent. If the entire walk is only 20 feet long and the rise is four tenths of a foot, an entire one-foot contour may never cross the walk. Check the actual spot elevations to understand how the proposed connection drains.

A sheet drawn at one inch to twenty feet

Two adjacent one-foot contours at a five percent slope are about twenty horizontal feet apart along the steepest direction. At the stated sheet scale their spacing is approximately one inch. Measure obliquely and the gap appears larger. Use the direction of steepest change when checking the implied grade.

Working procedure

  1. Read the field record. Find a known benchmark, the unit used for both coordinates and elevation, and the limits of the survey. Note whether historical coordinates use the former US survey foot. If the file lacks a datum description, retain that uncertainty in the drawing notes until the surveyor confirms it.
  2. Set the parcel spacing. Open the parcel preset to see a gentle grade, or bring survey points for the actual lot. Choose one foot for close inspection and two feet for a simpler contextual view. Compare the contour crossings at the driveway and rear yard before deciding which spacing suits the sheet.
  3. Check signs and slopes. Read the section from its marked starting side. Calculate a spot-to-spot grade using the rise and horizontal distance in feet. Visit the front, center and rear of the lot in the data. A globally correct elevation range can hide a local reversal caused by a transposed or erroneous observation.
  4. Issue a referenced background. Retain the legal boundary in the surveyor's reference and place the terrain as a distinct drawing layer set. Give the receiving drafter the unit convention, the interval, a known reference elevation and the source date. Label synthetic practice data distinctly if a demonstration accompanies the project file.

When to use this workflow

Driveway and pad feasibility

A few one-foot lines across a lot help locate the likely uphill side and compare potential approaches. Breaks in slope near a curb or apron often require additional measurements. Keep those points available for the designer who must reconcile the road connection with the proposed slab elevation.

Subdivision exhibit backgrounds

Two-foot lines can reduce clutter where recorded lot lines, easements and dimensions already fill a small sheet. Distinguish topographic lines from property lines with a clear legend and appropriate plot weights. Identify the source survey and its date so reviewers can interpret grading changes made after that survey.

Technical questions

Can a plat image supply the terrain heights automatically?

A scanned plat is a picture of lines and annotations. This workbench uses numeric coordinates and elevations from a grid or point file. Obtain the measured data or prepare a checked digital survey before contouring. A boundary outline alone does not describe the slope within the parcel.

When do one-foot increments show too much apparent detail?

If the source spacing skips an important swale or the vertical uncertainty is large compared with a foot, the map can imply unsupported precision. Inspect the original observations and use independent checkpoints. A wider interval may communicate site context more honestly while new measurements are collected.

Which foot is used to convert the exported interval?

The workbench uses the international foot, exactly 0.3048 meters. Historical US survey-foot coordinates use a slightly different length definition. Check the source metadata before combining those files, particularly when large coordinate values and regional control are involved.

Will these contours define a legal property corner?

A contour records an elevation across the sampled terrain. Property corners come from boundary evidence, survey control and the recorded legal description. Keep the parcel reference intact and align the terrain through verified control when overlaying the two types of information.

Terrain workflows