Set the scale in three dimensions
A studio model has two scales to keep track of even when both are nominally the same. The plan scale determines how wide a plot, street or building should be. The vertical scale determines how much model height represents a meter of elevation. When the real contour interval and the chosen board thickness do not agree at the selected scale, the built model has a different vertical scale from its plan.
Start by making the conversion for one sheet. At one to one thousand, one millimeter represents one meter on the ground. A three millimeter sheet therefore represents three meters when the model is true to scale. At one to five hundred, that same sheet represents only one and a half meters. The material has not changed. The relation between the physical object and the landscape has.
Count surfaces carefully when reporting relief. The top of a six-sheet layer stack is five thicknesses above the top of its first sheet. The entire stack is six thicknesses tall before glue or backing. These numbers answer different questions. Write down which surface represents the datum and use that same reference when setting the elevation of a building model or a bridge abutment.
Model-scale conversions for horizontal and vertical dimensions
| Parameter | Specification |
| At 1:500 | 1 mm represents 0.5 m |
|---|
| At 1:1000 | 1 mm represents 1 m |
|---|
| 3 mm at 1:500 | 1.5 m of terrain |
|---|
| 3 mm at 1:1000 | 3 m of terrain |
Worked examples
A 120 meter block at 1:500
Convert the block width to 120,000 millimeters, then divide by 500. The resulting model width is 240 millimeters. A six meter rise over the block becomes twelve millimeters. Four three-millimeter changes in level reproduce that rise between the first and last represented surfaces, before adding a backing board.
A campus at 1:1000
A 360 meter campus spans 360 millimeters on the model. A ten meter rise should occupy ten millimeters vertically. If you represent five two-meter intervals with three-millimeter sheets, the visible change becomes fifteen millimeters. The relief is exaggerated by a factor of 1.5 and should be labeled accordingly.
A shared building and terrain seam
A model footprint falls across three site layers. Mark the building outline in the same coordinate frame on each applicable template. Decide whether the building rests on a plinth, fits a cut recess or simply sits on the uppermost plate. A dry card mock-up reveals visible gaps before the finish material is committed.
Working procedure
- Start with the presentation footprint. Measure the available baseboard and the length of the real site. Convert the real dimensions to model millimeters at both candidate scales. Allow room for alignment and an edge treatment where the site is cropped. Check whether the architectural mass already has a fixed model scale.
- Match elevation and board. Measure stock thickness and calculate the real height represented by one sheet at your selected scale. Compare it with the available source intervals. If they differ, choose different stock, adjust the interval where supported or document the resulting vertical exaggeration. Count the backing board separately.
- Inspect terrain around the mass. Compare the shape and width of narrow ridges with what your material can hold. A model cut line may represent a full meter on the ground. Decide which close details remain legible, then check the footprint and entrance heights on a section through the proposed building.
- Prepare an assembly reference. Use the proof and slice sequence to mark the bottom, north direction and a reference edge. Arrange the pieces from lowest to highest before gluing. Place the building and any neighboring masses during a dry fit. Check the final height against the drawing scale before closing a surrounding frame.
When to use this workflow
Architectural jury models
A 1:500 base can communicate the transition from a street to a building platform while remaining compact enough to carry. Consider how much surrounding context the jury needs. A larger crop at a smaller scale may better explain the wider valley, access route or urban edge.
Removable terrain for option studies
A stack with repeatable registration lets a studio exchange the area around a courtyard, retaining wall or proposed plinth. Keep an untouched baseline and label each design alternative. Separate removable components cleanly so replacing one option does not require realigning the rest of the model.
Technical questions
How much real relief does 3 mm board show at 1:500?
Three millimeters multiplied by 500 gives 1,500 millimeters on the ground, or 1.5 meters. A two-meter source interval would ideally rise four millimeters at this scale. A three-millimeter sheet for that interval compresses the terrain vertically to three quarters of true-scale relief.
When does 1:1000 make more sense than 1:500?
At 1:1000 the same ground footprint uses half the width and one quarter of the baseboard area. This can accommodate a campus or watershed context. A threshold, small retaining wall or narrow path will also be smaller, so check whether those features must be read physically.
Should backing board count as an additional terrain level?
Treat backing as a supporting component unless its upper surface is explicitly part of the elevation model. Its thickness changes the overall object height but need not change the difference between two contour surfaces. Dimension the display frame from total thickness and label terrain relief separately.
Can I cut any foamboard using the laser SVG?
The SVG supplies geometry and dimensions. Check the exact board composition and your equipment's approved material list. Some foams and coverings are unsuitable for laser processing. For hand cutting, use a correctly scaled outline template and verify a known dimension on the printed sheet before cutting the board.