Put the relief in the blank’s coordinate system
A landscape may rise hundreds of meters above its survey datum, while the intended relief sits inside a piece of stock only a few centimeters thick. Subtract a reference height before positioning the part. If the highest point marks the model top, each lower contour represents a depth below that point. A model based on 800 through 840 meters contains 40 meters of relief. It does not need to carry an 800 meter pedestal unless that pedestal has a specific design purpose.
A contour by itself is an edge. It does not identify the side from which material should be removed. Around a summit the inside of a loop is generally high. Around a depression it may be low. Read the adjacent elevations and the section before deciding whether the loop bounds a pocket, an island or a terrace. Open contours along a cropped site also require a deliberate part boundary.
Keep the drawing that represents the surveyed terrain and the model derived for manufacture as separate revisions. A designer can alter the physical scale, exaggeration and backing thickness while retaining a path back to the elevations that generated the part.
Manufacture settings to distinguish from terrain spacing
| Parameter | Specification |
| Roughing strategy | 3D Adaptive Clearing |
|---|
| Axial depth control | Maximum Roughing Stepdown |
|---|
| Finish allowance | Stock to Leave |
|---|
| Vertical bounds | Top Height and Bottom Height |
Worked examples
A relief inside a shallow blank
A 60 meter elevation range occupies 12 millimeters at one to five thousand. An 18 millimeter blank then has six millimeters available below the lowest modeled point if the summit touches the stock top. Allow for surfacing, workholding and your required backing before treating that allowance as usable depth.
A shelf cut in several passes
Suppose the next terrace lies three millimeters below the current level. If the chosen roughing strategy permits a maximum one millimeter axial step under the verified setup, it takes at least three depth increments to reach that terrace. The geometry still contains a single three millimeter change in elevation.
A slot between close ridges
Two ridges are ten meters apart on the ground. At one to five thousand the gap is two millimeters wide. A tool four millimeters in diameter cannot enter that full gap at the same depth. Increasing the model size or accepting a smoother valley may preserve the surrounding landform more effectively.
Working procedure
- Write the scale equation. Decide how broad the finished relief should be and calculate its horizontal scale. Multiply terrain meters by one thousand and divide by the scale denominator for model millimeters. Apply the same calculation to the full vertical range. Record a separate multiplier if the design intentionally exaggerates the relief.
- Pick a reference plane. Identify the highest intended finished point and its relationship to stock top. For each slice, subtract its elevation from the reference elevation, then convert the difference to model units. The resulting depth is positive downward as a planning quantity. Translate that convention into the coordinate system used by the setup.
- Build machinable geometry. Inspect the imported profiles in Fusion and assign sketches or construction planes at the intended model heights as necessary. A workflow that inserts DXF into a single sketch may flatten elevated entities. Construct a checked surface, solid or series of terraces before using those features as machining selections.
- Verify a simulated section. Inspect the simulated stock at a traverse through the deepest valley. Compare remaining thickness and the height of each shelf with your hand calculation. Make sure the tool and holder can reach the selected geometry. The depth interval on this page alone cannot determine a suitable cutting strategy.
When to use this workflow
A stepped exhibit relief
Discrete terraces make an elevation interval physically legible in a museum or classroom model. Track each shelf as a design height and select an appropriate CAM strategy afterward. Preserve a wide enough land at narrow ridges for the chosen model scale and material.
Planning a continuous surface model
A series of contour sections can guide construction of a surface for finishing. Inspect the surface where contour topology changes around saddles. A smooth-looking loft can connect unrelated ridges if guide ordering is wrong. Compare horizontal sections cut back through the model against the source outlines.
Technical questions
Is a contour interval the same as a roughing step-down?
The interval expresses vertical separation in the source terrain. The roughing step-down limits axial engagement per machining pass in model space. They become comparable only after scaling, and even equal numerical values serve different purposes. CAM strategy and the actual tool setup determine the cutting parameters.
Why did my relief become taller than the stock?
Compare the selected Z reference and the scale applied to the height range. Scaling plan geometry to fit the blank while leaving survey elevation values in full-size units can create an enormous relief. Subtract the chosen datum and convert the resulting height differences before judging the stock fit.
Does the Fusion export include toolpaths or G-code?
The deliverable supplies contour geometry for modeling and planning. Program the part in Fusion Manufacture using the actual stock orientation, machine, cutter, fixtures and desired finish. Verify the simulated result and post-process for the specific machine only after completing the setup review.
Can a ball end mill preserve a pointed ridge exactly?
The tool's radius and the available access affect the surface it can reach. A narrow concavity may remain rounded, and a ridge can change appearance with finishing direction and stepover. Inspect the simulated cross-section at the final part scale to see which differences are material to the model.