Combine line spacing with the direction of travel
On a uniformly sloping plane, contours of equal vertical increment lie a constant horizontal distance apart along the fall line. One meter of rise over ten horizontal meters is a ten percent grade. Walk diagonally across that plane and you travel farther before reaching the next contour. Walk along the contour and the elevation stays constant. The surface, the chosen travel direction and the distance between stations are distinct parts of the same calculation.
A section also has a scale on each axis. Stretching the vertical axis makes gentle terrain easier to see on screen, but the visual angle of the plotted line no longer matches the physical slope angle. Use numerical rise and run when communicating a grade. Give the two station positions as well as the resulting percentage so that another reviewer can check the result.
A DEM usually supplies a continuous upper surface. It need not capture water moving below that surface through a culvert or behind a retaining wall. Conversely, a depression in a coarsely sampled surface may be an artifact. Use the display to prioritize investigation, then reconcile the elevations with the structures and surveyed breaklines involved in the site’s actual drainage.
Quantities used in a grade calculation
| Parameter | Specification |
| Slope numerator | Vertical rise |
|---|
| Slope denominator | Horizontal run |
|---|
| Ratio to percent | Multiply by 100 |
|---|
| Worked grade | 2 m over 40 m = 5% |
Worked examples
A four percent approach
A line climbs 0.8 meters over a horizontal distance of 20 meters. Dividing 0.8 by 20 and multiplying by 100 gives four percent. The distance along the sloping pavement is marginally longer. For an accurate comparison with a design grade, use the horizontal distance between the two stations.
A swale crossing two contour levels
A draining swale often bends the contours into a V pointing toward higher ground. Check several elevations in sequence and read the section across the channel. A single V is ambiguous when neighboring elevations or the true outlet are missing. Mark the observed low points before tracing a plausible flow direction.
A ridge with a nearly level crest
Two sides of a ridge may each exceed fifteen percent while a section taken along the crest remains nearly level. The band describes local terrain steepness. The section measures change along one selected direction. Rotate your interpretation to include the fall line before describing the whole ridge with one grade.
Working procedure
- Set a useful interval. Choose an elevation increment that yields readable separation across the area of interest. A one-meter step can reveal transitions near a building pad while a much larger step can hide them. Check the input point spacing as well. Fine increments alone cannot supply missing measurements along a ditch.
- Find likely divides and outlets. Start at a known high or low spot and follow the direction of neighboring contour values. Read the slope distribution for the extent, then use line spacing to locate abrupt transitions. Identify depressions and possible outlet points on the plan, but check site structures and field observations before assuming the water can actually follow that route.
- Compare section and spacing. Calculate the rise divided by horizontal run between two stations on the profile. Compare that average with the range of grades in the site-wide distribution. If they differ, consider whether the section cuts the terrain diagonally, crosses several grades or spans a sharp transition that a simple endpoint calculation averages out.
- Record the limits of the interpretation. Note any culverts, walls, inlets, fill edges or data gaps that the elevation grid does not represent. Keep measured levels and design proposals separate in the CAD issue. A useful markup identifies the locations where another field shot would resolve an important uncertainty.
When to use this workflow
Selecting a route for closer study
Slope bands can narrow the choice of corridors for a walking route, service drive or terrace. Review the longitudinal profile and the crossfall independently at candidate locations. Design requirements depend on the intended use and project jurisdiction, so establish those requirements separately during detailed design.
Comparing existing drainage patterns
The contour plan can identify likely gathering points and catchment divides. It can also highlight places where sparse input is least trustworthy, such as a low saddle between two lots. A drainage assessment additionally needs structures, surface treatment and hydrologic assumptions that are outside a basic contour extraction.
Technical questions
Is a 45 percent grade the same as a 45 degree slope?
Grade in percent is one hundred times the tangent of the slope angle. A 45 degree slope rises one unit per horizontal unit, which equals 100 percent. A 45 percent grade rises 0.45 units for each horizontal unit. Keep units visible when reporting a slope.
Why is my profile gentler than the steep grades in the distribution?
A profile follows a chosen direction. The steepest local slope follows the fall line, which can run obliquely to the section. A section that parallels a contour can show very little rise even across a hillside with a high local slope percentage.
Can a closed low contour prove water will pond?
It indicates a potential depression at the resolution of the terrain. An inlet, pipe, small diversion or an unmeasured saddle may provide a route out. Inspect drainage structures and outlet elevations on site before estimating storage or using the apparent depression in a design.
What should I inspect when contour spacing changes sharply near an edge?
Check whether the source actually captures a slope break there. Missing neighbors, interpolation across a sparse area and the boundary of the grid can affect the derivative used for a slope calculation. Compare the tightly spaced contours with nearby observed elevations and with a section through the transition.