TopoContourDXF

Rhino terrain contours for surface modeling

Import elevated DXF curves into Rhino, fit a Patch for a continuous landform or use closed contours with PlanarSrf for stepped plates. A mesh or surface can then support Drape. Preview free. Three exports cost $14.99.

Terrain viewport

Terrain sheet
Loading terrain…Synthetic DEM
Elevation range—
Index / minor—
Polyline vertices—

Elevation profile

A — A′
48%

Slope distribution

% GRADE

Free proof

Download a watermarked plan or the five highest contour elevations.

PROFESSIONAL EXPORTS

Pro Preview

DXF / SVG / GIS

Project pack 3 exports
CAD Pro Unlimited
Engineering Studio Unlimited

Choose a surface according to the next operation

The same DXF can serve a smooth presentation model, a set of horizontal plates or a background for section drawings. These require different geometry. A continuous fitted surface lets you intersect a facade plane at any bearing. A planar face encloses the area of a plateau at one specific height. In a stepped assembly, the missing vertical transitions are intentional and become visible side faces when the plates gain thickness.

Start by orbiting the imported lines without rendering a surface. Look for duplicate elevations, rings that end at the frame and widely separated parts with the same Z value. The spaces between those curves are places where the modeler must interpolate. A narrow summit represented by one last loop gives less control over the top of a surface than a measured spot at its center.

Document the transformation from survey coordinates to the model origin. A convenient local origin improves everyday modeling, while collaborators may later need to put the design back in its survey position. A known translation, rotation and unit conversion allow the two files to align without visually fitting a building to the nearest contour.

Rhino Patch controls for terrain curves

ParameterSpecification
Fitted surface commandPatch
Guide geometryCurves
Fit samplingSample point spacing
Surface flexibilityStiffness

Worked examples

A cone with a missing summit

A circular guide at 220 meters and a smaller ring at 230 meters constrain the sides of a cone. The space inside the inner ring has no higher constraint. If a survey supplies a 234 meter summit, include that point during fitting. Otherwise show the upper region as an approximation.

Two islands in one elevation plane

Two detached loops at the same height can become two separate planar faces. Select the closed loops and inspect their boundaries after PlanarSrf. When one loop lies inside another, decide whether the inner loop represents a hole in a plate or an independent higher feature mistakenly assigned the same Z.

A smooth background beyond a building

A distant ridge in a perspective view benefits from a lightly fitted surface. Fit the guide curves first, then view the silhouette from the intended camera. A lower control count is easier to edit. Check the same object in section where it passes close to an entrance or retaining wall.

Working procedure

  1. Measure in document units. Compare the imported distance between two known plan coordinates with the expected distance in the Rhino file. In a millimeter document, six meters should measure six thousand units. Check the Z distance between two successive guide curves before centering the model or moving it to a studio origin.
  2. Separate curves by job. Put the imported contours on reference layers, leave any annotation on its own layers and work on duplicates. Use a right or front viewport to find flattened or misplaced curves. Inspect clipped lines at the footprint perimeter. Their open ends may be perfectly valid guides for a fitted surface.
  3. Build a comparison surface. For Patch, fit an initial low-complexity surface through representative guides. Adjust sampling and flexibility while studying the cross-section rather than continually adding more spans. For a stepped alternative, select coplanar closed loops and build planar faces at their original heights. Keep the two alternatives on separate layers.
  4. Measure the fit. Intersect the fitted surface with horizontal planes at a few known elevations and compare those intersections with the imported guides in plan. Check the valley floor as well as a broad hillside. A surface that follows the easy, widely spaced area may still bridge a sharp ravine.

When to use this workflow

Concept terrain for architectural massing

A gently fitted landform can give a model the continuous skirt needed around a building study. Keep the measured guides visible on demand so a reviewer can see where the surface interpolates. Close the ground plane or trim its border only after fixing the architectural placement.

Terraced presentation geometry

A set of planar faces can act as terraces, foam slabs or diagrammatic floors. Extrude each by the desired model thickness when solids are required. A hole in one elevation plane needs a matching boundary policy in neighboring layers if the assembled object is intended to read as a coherent relief.

Technical questions

Will Patch pass through every contour vertex exactly?

Patch fits a surface to constraints. Sample spacing, surface spans and stiffness affect the result. Evaluate the fit by cutting sections or horizontal intersections through the finished surface. Increase complexity only when the deviation matters at the location and scale where the model will be used.

Why does Drape ignore my wire contours?

Drape samples meshable geometry viewed from a construction plane. Bare curves supply no surface to sample. Create a suitable mesh or surface first, orient the viewport and run Drape over that object. The sampling spacing influences how much of a narrow feature reaches the result.

Why does PlanarSrf leave a hillside edge open?

A clipped contour that reaches the grid boundary often has two endpoints. A planar face requires a closed coplanar boundary. If you need a physical plate, build the intended edge along the actual model perimeter and inspect the new loop before generating a face.

How can I preserve my original survey curves while fitting?

Import the DXF onto named reference layers, lock those layers and duplicate the selected guides to a working layer. Name each trial surface with its settings. When comparing versions, a section plane in a fixed location is a more reliable reference than an orbit view with a different camera.

Terrain workflows