Budget vertices where the terrain changes direction
Sandbox creates faces between vertices on the selected contours. A large number of edges along a straight hillside increases the work done by the importer and the model, even when those edges add almost nothing to the visible shape. At a sharp channel bend the same number of vertices can carry real information. Compare two areas with different geometry before deciding on a reduction setting for an entire parcel.
Vertex tolerance is a ground distance in this workbench. If the final view will be a broad neighborhood perspective, a modest displacement may be imperceptible. If a doorway meets a path at the same location, the resulting section deserves closer review. The height of each retained contour stays constant, but moving a horizontal crossing can change the interpolated terrain elevation beneath the doorway.
For a repeatable test, keep the starting curves in a locked group and create the candidate terrain in another. Use the same section plane and camera for both versions. Check the crown and the lowest point of the slope, then compare their relationship to the building. That short inspection says more about the result than a smooth material or a favorable sun angle.
Geometry expected by SketchUp Sandbox
| Parameter | Specification |
| Terrain toolset | Sandbox |
|---|
| Build operation | From Contours |
|---|
| Input geometry | Contour lines |
|---|
| Surface representation | Triangulated irregular network |
Worked examples
A yard in a feet-based template
Two surveyed corner marks lie 80 feet apart. Their separation in SketchUp should also read 80 feet after import. If the width looks plausible but the Tape Measure tool reports a different dimension, check the DXF import units before resizing your furniture or altering the terrain.
A line with too many tiny edges
A gentle bank can arrive as hundreds of short edges tracing almost the same arc. Increase the simplification tolerance slightly and compare the curve against its original. Check the tight turn around a driveway apron separately. A tolerance suitable for the bank may erase the apron detail.
A U-shaped footprint
An imported site wraps around an unmeasured courtyard. Sandbox may span the courtyard with a fan of triangles because the outer edges suggest a larger continuous area. Enable Hidden Geometry, inspect the faces and trim to a checked footprint. Keep the source boundaries separate for later verification.
Working procedure
- Establish a reference length. Choose a measurement from the survey that also remains recognizable in your model. Record the ground unit, model unit and expected length. This check is easier to conduct before adding trees, shadows and buildings, when an oversized or undersized terrain can still look convincing.
- Reduce only surplus detail. Take an initial vertex reading, then try a modest tolerance on one region. Watch for corners around retaining structures and abrupt changes beside steps. If simplification brings two adjacent contours together in plan, restore the previous setting and consider a smaller study extent instead.
- Select the contour edges. Import the file with its elevation information intact. Enter the relevant editing context or make a working copy if the importer wrapped the geometry in a group. Exclude text strokes, frame edges and scale marks from the selection. Run From Contours on the resulting set.
- Inspect the new group. Turn the edge overlay on and orbit along the site boundary. Check for spikes, isolated faces and triangles reaching beyond the survey. Cut a section across the building location and compare a known height difference with the source before applying materials or softening the mesh.
When to use this workflow
Early massing against an existing slope
A building study can sit on a lightweight terrain group while the architect evaluates views and access. Put the mass and terrain in separate editing contexts. Retain the original unmodified terrain if you plan to model alternative excavation outlines or several grades for the same entrance.
A presentation model shared with a studio
A clean mesh is easier to navigate on a laptop and easier to distinguish from architectural geometry. Give the recipient the chosen interval and the location of the reference length. Those two numbers help detect import scale mistakes when the group enters a different SketchUp model.
Technical questions
Why did Sandbox create a flat patch?
Inspect the source edges from the front or side. A CAD import setting that projects everything to one plane can remove all vertical separation. Select two contours and verify their respective heights before rebuilding terrain. Widely spaced contours across a truly level area can also produce broad flats.
Can I select the border when I run From Contours?
Exclude the border unless it is a measured terrain constraint with a known height throughout. A decorative rectangle can pull triangles toward its own plane. Keep it as a reference for trimming the final terrain and store that trimming outline outside the terrain editing context.
How do softened edges affect my terrain measurements?
Softening changes how adjoining faces display and how the surface appears under light. The underlying triangular geometry remains available when you reveal hidden edges. Use a section or measurement against that geometry to assess a grade. Smooth shading alone can conceal an awkward face transition.
Which SketchUp setup do I need for this handoff?
Use an edition and import configuration that supports CAD DXF with elevations and provides Sandbox From Contours. Verify those options in your installation before preparing a batch of sites. A flat image import gives a visual underlay but does not give Sandbox editable elevated edges.